Amount Of Charge Flowing Through A Wire Each Second Tips For Troubleshooting The Tuttnauer Autoclave Water Pump

You are searching about Amount Of Charge Flowing Through A Wire Each Second, today we will share with you article about Amount Of Charge Flowing Through A Wire Each Second was compiled and edited by our team from many sources on the internet. Hope this article on the topic Amount Of Charge Flowing Through A Wire Each Second is useful to you.

Tips For Troubleshooting The Tuttnauer Autoclave Water Pump

If you are experiencing problems with the water pump in your Tuttnauer autoclave, you need to find and fix the problem right away. No water or a water level that is too low means your machine is not working properly and will not fully sterilize your device. And that means unless you fix the problem, you’re basically out of business.

If you’ve always sent your autoclave in for repair whenever a problem occurs, you know how expensive that repair can be. You have labor charges, parts charges, and don’t forget shipping and handling charges. When all is said and done you can almost buy a new machine! If you are having trouble with water in your Tuttenauer autoclave, here are some troubleshooting tips that may help you fix the problem yourself.

  • If the water is flowing in the wrong direction, check the two tubes connected to the pump. It may be that you just need to reverse them.
  • If the pump makes noise, check if the mounting bracket is loose or broken. You may need to tighten it or replace it. If it’s not the bracket, the problem is probably the pump itself and you’ll need a new one.
  • If the water pump keeps blowing fuses, first look for pinched or twisted wires that could cause a short. If this is not the problem, turn off the pump and disconnect the wire from the No. 1 and 2 terminals on the solid state relay. Turn the pump back on and if the fuse blows again the problem is either the water pump or the pump capacitor and you will need to replace both.
  • If the pump does not turn off you need a volt/ohmmeter to check the relay. Read between TP13 and TP1. A 10 to 12 volt DC signal is required to tell the relay to turn off, and a 0 to 1 signal is required to turn it on. If the reading is anything else, it means you have a problem with the control circuit.
  • If the signal is correct, repeat the process on the relay. And if you get a wrong signal there, you will need to replace the Ajunc board.
  • If your pump does not turn on, the first thing you need to do is check the fuse and replace it if necessary. Next, look for pinched or twisted wires going from the solid state relay to the pump. If that doesn’t help, turn off the power to your autoclave and disconnect the wires from terminals 1 and 2 on the relay. Now connect those two wires together and turn the pump back on. If the pump still doesn’t work, you may need to replace it.

While your autoclave may be a ‘machine’ and perform a very important, life-saving function, it’s still just a big box with a few basic working parts. It’s usually easy enough to spot the problem. And most of the time you can fix it yourself!

Video about Amount Of Charge Flowing Through A Wire Each Second

You can see more content about Amount Of Charge Flowing Through A Wire Each Second on our youtube channel: Click Here

Question about Amount Of Charge Flowing Through A Wire Each Second

If you have any questions about Amount Of Charge Flowing Through A Wire Each Second, please let us know, all your questions or suggestions will help us improve in the following articles!

The article Amount Of Charge Flowing Through A Wire Each Second was compiled by me and my team from many sources. If you find the article Amount Of Charge Flowing Through A Wire Each Second helpful to you, please support the team Like or Share!

Rate Articles Amount Of Charge Flowing Through A Wire Each Second

Rate: 4-5 stars
Ratings: 9846
Views: 96159669

Search keywords Amount Of Charge Flowing Through A Wire Each Second

Amount Of Charge Flowing Through A Wire Each Second
way Amount Of Charge Flowing Through A Wire Each Second
tutorial Amount Of Charge Flowing Through A Wire Each Second
Amount Of Charge Flowing Through A Wire Each Second free
#Tips #Troubleshooting #Tuttnauer #Autoclave #Water #Pump

Source: https://ezinearticles.com/?Tips-For-Troubleshooting-The-Tuttnauer-Autoclave-Water-Pump&id=6723715

Related Posts