Add 1 Inch Pvc And 2 Inch Pvc Flow How to Install a Sand Trap Drain

You are searching about Add 1 Inch Pvc And 2 Inch Pvc Flow, today we will share with you article about Add 1 Inch Pvc And 2 Inch Pvc Flow was compiled and edited by our team from many sources on the internet. Hope this article on the topic Add 1 Inch Pvc And 2 Inch Pvc Flow is useful to you.

How to Install a Sand Trap Drain

If a property does not have a proper drainage system, it can result in severe flooding in yards, basements, and even garages. Since soil particles come in different sizes, soil permeability can vary. For example, a soil with small particles is called a cohesive soil. Also, there is soil with larger particles such as gravel and sand. If you are experiencing flooding problems in your basement or garage, you may need a special type of drain called a sand trap drain.

Structures built on cohesive soils can eventually suffer serious structural damage from flooding that will make repair work expensive. These drains are designed for soils with low permeability. Permeability is the property of a soil’s pore system that allows water to flow. In terms of permeability, the general rule is that the smaller the particle size, the lower the permeability of the soil. A sand drain is a hole dug in a cohesive soil and filled with sand. Because sand has larger particles, it has a higher permeability; This will allow water to flow through it more easily and allow for proper drainage.

A general guide on how to install a sand trap drain is as follows:

1. When installing this drain, the height of the concrete foundation above the floor should be about 5-6 inches. It’s important to make sure you have enough height from the floor before you start the project.

2. Once you have an accurate height measurement, draw a line with a pencil around the perimeter of the area where you are installing the drain. Use a utility knife to cut the lines on the drywall. After cutting, remove the bottom pieces.

3. The base of the drywall must be replaced with plywood. About 2 or 3 inches of drywall should be enough. Install the plywood. Any drain pipes shall be secured above the drain pipe passing along the sand trap. Also, pipes leading into the sand trap should be secured at least six inches above the bottom of the trap. An elbow piece should be attached to the sand trap drain to divert water through the drain system and away from the flood prone area. Remember, the sand trap requires a 2-inch vent.

4. Place the sand trap down the drain and create a trough about 4 to 6 inches wide on each side diagonally across the trap.

If you don’t have proper drainage, heavy rains and melting snow can cause excess water to accumulate. If you are a homeowner with a lot of water logging, a sand trap drain may be the solution. If the sand trap is for a garage, a metal grate secured to the drain will allow people to walk or drive over the trap without damaging it. Many experts recommend building a custom sand trap drain; However, you can buy them as pre-made sand trap drains.

Video about Add 1 Inch Pvc And 2 Inch Pvc Flow

You can see more content about Add 1 Inch Pvc And 2 Inch Pvc Flow on our youtube channel: Click Here

Question about Add 1 Inch Pvc And 2 Inch Pvc Flow

If you have any questions about Add 1 Inch Pvc And 2 Inch Pvc Flow, please let us know, all your questions or suggestions will help us improve in the following articles!

The article Add 1 Inch Pvc And 2 Inch Pvc Flow was compiled by me and my team from many sources. If you find the article Add 1 Inch Pvc And 2 Inch Pvc Flow helpful to you, please support the team Like or Share!

Rate Articles Add 1 Inch Pvc And 2 Inch Pvc Flow

Rate: 4-5 stars
Ratings: 8980
Views: 29493349

Search keywords Add 1 Inch Pvc And 2 Inch Pvc Flow

Add 1 Inch Pvc And 2 Inch Pvc Flow
way Add 1 Inch Pvc And 2 Inch Pvc Flow
tutorial Add 1 Inch Pvc And 2 Inch Pvc Flow
Add 1 Inch Pvc And 2 Inch Pvc Flow free
#Install #Sand #Trap #Drain

Source: https://ezinearticles.com/?How-to-Install-a-Sand-Trap-Drain&id=5392806

Related Posts