Add 1 Inch Pvc And 2 Inch Pvc Flow How to Build Your Own Koi Pond Filter – That Really Works Great – Guaranteed

You are searching about Add 1 Inch Pvc And 2 Inch Pvc Flow, today we will share with you article about Add 1 Inch Pvc And 2 Inch Pvc Flow was compiled and edited by our team from many sources on the internet. Hope this article on the topic Add 1 Inch Pvc And 2 Inch Pvc Flow is useful to you.

How to Build Your Own Koi Pond Filter – That Really Works Great – Guaranteed

This is an article on how to build your own koi pond filter and the reason I’m an authority is because I built my own 6 years ago and it’s still going strong!

What exactly is a koi pond filtration system? What is a Fish Pond Bog?

They are also known as koi pond bogus. Here’s a quick overview of how it works. A marsh is usually built at the head of your pond, behind your waterfall. It is fed from the pool pump through a 2 to 2 1/2 inch hose at the other (far) end of your pool. And, once the water has filtered from the bottom of your bog, through all the lava rocks, it will flow through your waterfalls back into your pond, to cycle again.

Why not just buy the filter to install as it would be so much easier?

Of course, it’s easy enough to just go out and buy a fish pond filter to suit your needs. But why would you want to when you can build your own koi pond filter? It’s a filtration system that, if properly built, will give you years of care-free maintenance.

This article will detail how I built and designed my own pond bog and accompanying filter. But, first, let’s cover some facts about these filters.

Reasons to build your own koi pond filter:

If you build it right, this will be the last time you need a koi pond filter. The reason I say this is because once you build and install your own pond filter, it will immediately begin to set up a biological process that will keep your fish healthy and your pond water nice and sparkling clean.

Once you build your own pond filter (bog), additional filters are not needed. This will save you a lot of money over the lifetime of your pool. If you decide to add water features, you may need to add a small pond filter. However, these water features use very small and inexpensive filters to keep the water running smoothly through them.

While clearing the swamp to get into your filter is a dirty job if your pond develops a problem, it’s actually not very likely. As an example, my pond’s bog and filter have now been in place, 24 hours a day for 6 years – 7 days a week and 365 days a year, with no problems! And, my pond is about 32 feet by 12 feet by 3 feet. It holds approximately 3,000 gallons of water and is home to approximately 150 koi at one time. These bog filtration systems work! And, they work beautifully.

The real beauty of a bog filtration system is that the longer it runs, the more biological balance is created for the fish in your pond. What’s really happening in the swamp is that as the water is filtered through the media, and I use lava rock, it works very well or drains the waste from the pond itself. The process by which it does this is through nitrification. This means that nitrifying bacteria (good bacteria) attach themselves to the inside of the swamp, and on an ongoing basis, these bacteria feed on additional nutrients such as organic matter and fish waste. It also helps create the perfect ecological pond water balance for your fish.

A typical lake marsh, built at the top of a lake or behind waterfalls, is like mine. Water is pumped from the other end of your pond through a hose and down the lava rock placed in your bog. Here it is filtered before once again going down the waterfall into our pond.

My pond’s swamp filtration system: My pond is approximately 6 feet wide X 4 feet high X 5 feet deep. It is made of cinder blocks or concrete blocks. It is acceptable to use bricks, stone or any stable construction medium suitable for underwater use. After you mortar these blocks together to create your bog, the inside and outside of these blocks need to be coated with fiberglass mortar and then painted with latex paint on the outside. We don’t want this bog out! After I built my bog as above, I lined the inside of it with an EPDM liner that should have a lifespan of about 20 years.

I allow a large portion of this EPDM liner to extend from the bog to the head of the falls. Then I placed my large flat stone on top of this liner to give my waterfalls.

Water is circulated through bogs in this way: From the pump at the far end of the pond, a 2-inch hose is run back and forth to the bottom of the pond (out of sight) and behind the bog. The hose goes up and up and down to the bottom of the bog from behind the bog. At this stage the water is filtered. Water from the pump is released into the bottom of the swamp and rises through approximately 3-4 feet of lava rock. It does a great job of filtering and keeps the pond water clean keeping the fish happy and you happy because your workload and potential filter problems are now virtually eliminated.

How is water evenly distributed through a bog’s lava rock filtration system? At the end of the well, the hose, a prefabricated piece of equipment is installed.

It’s just a 2-inch length of PVC attached to the end of a hose that extends to the bottom of the pool, below the lava rock.

At the end of this PVC extension is another piece that is attached before you cover it with lava rock. This piece is attached to a long straight PVC pipe and glued together to form a U at the end. Now, here’s the important part….. you need to cap the ends of the U PVC pipe so that all the water doesn’t just come out in a solid stream. Now you will drill a maximum of 1/4 inch holes in the U shaped PVC. It is through these holes that you have just drilled that your pump water will come out from under the lava rock.

As you can imagine, the pressure will force the water out of all the holes in your PVC pipe and filter through all the lava rocks you put on it. It’s pretty easy to build and is one of the best pond filtration bog systems you can have.

The size you want to make this PVC piece will be determined by the width of the bottom of your bog. Otherwise, if the bottom of your bog is 4 feet, your PVC piece that ends up like a U should extend at least 3 feet to allow as much water to flow through the drilled holes as possible. Filter through lava rock.

We are not allowed to submit images with our articles so it is difficult to explain it all and try to make a point. But, if you want to get a mental image of the shape of a piece of PVC, a close up picture of its size can be compared to a 2 prong pitchfork. (Putting holes in the prongs.)

Of course, you don’t have to follow my design exactly. You can make this piece according to your own taste. For example, you might want 3 or 4 prongs instead of 2, and that’s fine too. There is no wrong way to build your waterfall as long as the water exits the hole and filters through your lava rock before re-entering the pool.

Video about Add 1 Inch Pvc And 2 Inch Pvc Flow

You can see more content about Add 1 Inch Pvc And 2 Inch Pvc Flow on our youtube channel: Click Here

Question about Add 1 Inch Pvc And 2 Inch Pvc Flow

If you have any questions about Add 1 Inch Pvc And 2 Inch Pvc Flow, please let us know, all your questions or suggestions will help us improve in the following articles!

The article Add 1 Inch Pvc And 2 Inch Pvc Flow was compiled by me and my team from many sources. If you find the article Add 1 Inch Pvc And 2 Inch Pvc Flow helpful to you, please support the team Like or Share!

Rate Articles Add 1 Inch Pvc And 2 Inch Pvc Flow

Rate: 4-5 stars
Ratings: 7230
Views: 79934822

Search keywords Add 1 Inch Pvc And 2 Inch Pvc Flow

Add 1 Inch Pvc And 2 Inch Pvc Flow
way Add 1 Inch Pvc And 2 Inch Pvc Flow
tutorial Add 1 Inch Pvc And 2 Inch Pvc Flow
Add 1 Inch Pvc And 2 Inch Pvc Flow free
#Build #Koi #Pond #Filter #Works #Great #Guaranteed


Related Posts